OMAX 60120 JetMachining Center

The small-footprint bridge-style OMAX 60120 JetMachining® Center is fast and accurate, ideal for a wide range of machining needs, with one of the lowest cost per part in the industry. The large table can cut stock up to 5’ x 10’, creating complex parts out of almost any material. Challenging hard, reflective, and nonconductive materials can also be cut, making the 60120 a valuable addition to existing shop capabilities. Accessories such as the Tilt-A-Jet® for taper-free edges, A-Jet® for 3D cutting, and the Rotary Axis for 6-axis machining increase versatility. The easy-to-use Intelli-MAX® Software Suite and the 60120 take you quickly from idea to reality.

  • Fastest cutting speeds and best precision compared to any abrasivejet in the industry and is backed by our exclusive IntelliMAX® Software with real world cutting data
  • Programmable Motorized Z-Axis with a precision OMAX MAXJET®5i Nozzle Assembly can boost cutting productivity and process efficiency
  • Tilt-A-Jet taper compensating abrasivejet cutting head (available as an option)
  • Patented Intelli-TRAX® traction drive inside the X-Axis beams fully enclosed inside coated steel covers
  • Highly efficient, industry-proven Generation 4 EnduroMAX® Pumps available up to 100 hp with operating efficiencies up to 85%
  • Rapid Water Level Control for quiet and clean submerged cutting
  • Bulk Abrasive Feed Assembly transports garnet from the assembly’s large hopper into the Zero Downtime Hopper located at the Motorized Z-Axis
  • Optional Variable Speed Solids Removal System (VS-SRS) designed for tough industrial use increases uptime through automated solids removal
  • Shipped as a completely pre-assembled and factory-tested system
  • Machines a wide range of materials and thicknesses, from metals and composites to glass and plastics
  • Does not create heat-affected zones or mechanical stresses
  • No tool changes and minimal fixturing reduces setup by 50% or more
  • No additional water required for pump cooling
  • Small, efficient footprint for minimal floorspace utilization
  • Leaves behind a satin-smooth edge, reducing secondary operations
  • No noxious gases, liquid and oils used in, or caused by, the machining process
  • EnduroMAX pump technology delivers the highest nozzle horsepower in the industry for faster and more efficient cutting
  • Completes most work below 80 dBA at one meter for submerged cutting
  • Environmentally “green” system with quiet and clean operation with low electrical consumption
  • Highly robust and reliable pump design capable of over 1000 hours between maintenance
  • Scissor-style hard plumbing for low maintenance and high reliability
  • Drive system sealed against water, dirt, and grit
Machine Dimensions
Footprint (with controller) 18’9” x 9’2” (5,715 mm x 2,794 mm)
Weight (Tank empty) 6,200 lb (2,812 kg)
Height (with scissor plumbing) 9’7” (2,921 mm)
Operating Weight 23,200 lb ( 10,545 kg)
Work Envelope
X-Y Cutting Travel 10’6” x 5’2” (3,200 mm x 1,575 mm)
Z-Axis Travel 8” (203mm)
Table Size 12’0” x 6’5” (3,658 mm x 1,956 mm)
Drive Description
  • Brushless servo motors
  • Pre-loaded ball screw with recirculating ball bearings and hardened precision ground ways in Y-Axis
  • Closed loop, digital drives
  • Intelli-TRAX drive technology with precision linear encoders in X-Axis
  • Precise Motorized Z-Axis
Standard Model Specifications
Material Support Slats 4" x 1/8" Galvanized Steel
Maximum Supported Material Load 400 lbs/ sq ft (1,950 kg/ sq meter)
Electrical Requirements 3-Phase, 380-480 VAC ±10%, 50-60 Hz
Noise Level Below 80dBA at one meter for submerged cutting
Speed 180 in/min (4,572 mm/min)
Linear Positional Accuracy ±0.001" (±0.025mm)
Repeatability ±0.001" (±0.025mm)
Ballbar Circularity ±0.003” (±0.076 mm)
Optional Accessories
  • Tilt-A-Jett® Cutting Head
  • Variable Speed SRS (VS-SRS)
  • Collision Sensing Terrain Follower (with Tilt-A-Jet only)
  • Z-Axis Drill
  • Precision Optical Locator (POL)
  • Water-only MAXJET 5 for cutting soft materials
  • OMAX Mini MAXJET 5i Nozzle Assembly
  • DualBRIDGE second bridge
  • Manual Tilt Z
  • Second MAXJET 5i with Motorized Z-Axis (requires second Y-Axis carriage)
  • Laminar Filter
  • Waterjet Brick Kit
  • Rotary Axis
  • Air and Water Conditioning Kit
  • A-Jet
  • Terrain Follower/A-Jet
  • Material Holding Kit
  • Laser Feature Finder

     (see more...)

*Optional accessories may reduce cutting travel. Photos may show optional accessories. For a complete list of accessories, contact an OMAX sales representative. Accuracy specifications are at 72° F (22° C) Pumps are built to meet UL and CE specifications. Contact OMAX for detailed utility requirements.